|     |   
Customer ServicePre Delivery Inspection
PDI- (Pre-Delivery Inspection) Read Fully Before Continuing Congratulations on your purchase! You have chosen wisely, the vehicle you have bought is one of the best available. Your vehicle has been supplied in a crate. This is NOT the same as buying a fully PDI’d (Pre Delivery Inspection) vehicle from a dealer. It is entirely your responsibility to ensure a qualified motorcycle mechanic puts your bike together correctly. Failure to do so may invalidate the warranty supplied with your bike. ***IF FULL PDI IS NOT PERFORMED, WARRANTY MAY BE VOIDED *** GUIDE FOR ASSEMBLY This document is supplied only as a guide to a professional and may not be complete. Each machine may require individual attention & therefore ONLY qualified persons should only carry out the following: - Remove vehicle & all accessories from crate & inspect to ensure all necessary parts have been supplied correctly - Mount shock (where applicable) - Tighten lower fork bolt, reached from underside of forks. (where applicable) - Mount front wheel & ensure free rotation – check for potential bearing &/or brake drag Ensure all frame bolts are tight (use thread lock compound where necessary) – use locking wheel nut (supplied) - Loosen triple clamps around fork legs & set desired fork height (where applicable). Use copper grease on triple clamp bolts to prevent damage to the alloy threads & then firmly tighten. - Fit handlebars and clutch cable to clutch lever - Pump front brake lever until firm (bleed if necessary). Check front braking system for potential leaks or damage by pulling brake lever very hard several times. Visually inspect all joints for leaks & remedy where necessary. Spin wheel(s) to ensure caliper is releasing from disk - Fit rear brake pedal where necessary & repeat procedure described for front brake - Check fluid levels, top up with DOT4 where necessary - Fit front mudguard using thread locking compound. (where applicable) - Fit foot pegs - Ensure the correct pressure in tires 20-30 PSI for off-road, 26 PSI for tarmac track. - Loosen rear wheel & adjust chain tension. Find tightest point in chain by spinning rear wheel, there should 15mm up & 15mm down at the longest section of chain with rider sat on vehicle. Ensure chain runs true & is on top of chain roller. Ensure chain does not foul on rear chain guide (use shims/washer to space if necessary) - Working from front to rear, ensure all nuts & bolts are tight. Where no nyloc nuts or spring washers are present, ensure thread-locking compound has been used. If none has been used during factory assembly, remove nut or bolt, apply locking compound & re-tighten. Pay particular attention to the following critical safety areas: Wheel nuts, brake caliper bolts (thread lock), Top & rear engine bolts (frame must be hard tight against the engine, use thread lock), chain tensioners, rear shock bolts, triple clamp bolts (yokes), Handlebars, brake/clutch/throttle, swing-arm, front & rear sprocket - Check all engine hardware is tight, (including but not exclusive): flywheel, inlet manifold, exhaust bolts, - Adjust tappets. Set engine to TDC (ONLY rotate engine anticlockwise) & check cam timing alignment (cam sprocket/cylinder head– adjust is necessary), remove tappet covers & adjust tappet clearances ~0.15mm - Fully ensure nothing is touching the exhaust system. On oil cooled models, ensure the oil cooler pipes do not touch the exhaust manifold & that the heat protection springs are located on the correct part of the pipe in order that should they touch the exhaust the heat will not damage them. - Ensure all cables pipes & wiring are away from moving components such as the wheels, use cable ties where necessary - Fuel bike & check for fuel leaks - If fuel leaks from carb overflow – remove carb & adjust float height. Check for any debris which may be blocking the fuel shut-off valve - Change oil with 10W40 Motorcycle Oil - Adjust tension for both clutch & throttle cables - Ensure wheel spokes are tight & wheels run true - Start engine & warm up (using choke if necessary). Set idle speed so engine ticks over comfortably without stalling or racing. - Test machine ensuring all gears are present & correct & that all controls are fluid & functional. Ensure brakes are working efficiently (bearing in mind that the pads will need to bed in prior to optimum performance) Engine break-in Run bike at no more than 2/3’s throttle & do not allow engine to rev to a high speed. Engine break-in should be no less than 2 hours. 2 Hour Service - After 2 hours carry out the following checks & procedures: - Drain oil & replace with 10W40 Motorcycle Oil - Check all nuts & bolts & tighten where necessary (use PDI data as reference) - Check flywheel nut - Check wheel spokes (especially rear wheel drive side) & tighten where necessary - Re-Adjust throttle cable & clutch cable if required - Re-tension chain - Check wheel bearings for any sign of wear of free-play - Check brake caliper operation & brake pad wear - Check spark plug gap ~0.6mm-0.7mm - Check tire pressures Riding Tips for Long Engine Life – IMPORTANT - Do not over rev your engine as you may cause damage to valves. This is particularly applicable where an inner rotor kit is used. Under load the engine is capable of revving into major valve bounce that can cause permanent damage to your engine. If you feel the power dropping off or start to hear valve bounce it is critical that you change up a gear or ease off the throttle. - It is good practice to carry out the above checks on a regular basis, ideally each time you ride your machine. We advise an oil change after every 10 hours use. - Do not stamp through the gears – always use the clutch. - If you miss a gear do NOT stamp into gear from high engine revs. -Do not drop your clutch heavily, or slip it unnecessarily. -Do not allow your air filter to fill with fuel – this can occur by incorrect float height setting – see above, or the bike falling onto its side. - If the engine back-fires while the air filter is filled with fuel, it may ignite – check air filter regularly while riding. Problem Solving - Exhaust Glows Red (fast tickover) – Carburetion too lean, richen mixture via raising needle - Engine misfires at mid to high engine speed, open throttle – Mixture too rich, drop needle - Engine Pops & bangs on over-run – mixture too rich, drop needle - Engine kicks back hard whilst starting – Ignition too advanced, or mixture too lean - Engine difficult to start – engine flooding or mixture too rich – check float height - Weak Spark – Pick-up coils too far from rotor (where inner rotor kit fitted) or bad earth - No spark – Either poor earth or faulty Rotor Coils/CDI/Coil/Lead/Cap/Plug – use moving coil multi-meter to diagnose - Fuel leaks from overflow – Floats set incorrectly or blocked by debris or sticking - Engine runs fine, but then starts to misfire – faulty rotor coils/CDI/Coil/Plug - Rattles from engine – Tappets set incorrectly - Engine will not tick over when warm – tappets set incorrectly - Engine will not return to idle & races – sticking throttle cable Storage • It is advisable to fully service and lubricate the bike prior to leaving the bike unused/unattended for any length of time • It is advisable to fully drain the tank and carb of fuel prior to leaving he bike unused/unattended for any length of time.

© 2011 XT Powersports. All rights reserved.   Fort Lauderdale Website Designers : Miami Website Designers